Swimming Pool Design and Installation
home pool design news blog
company gallery online shop environment
services case studies pool covers contact

Chlorine

Fi-Clor Sanitiser - Stabilised Chlorine Granules - -  
Used at the recommended levels, Fi-CLOR Granules rapidly produce free active chlorine to kill bacteria and other harmful organisms so that you have the peace of mind of knowing your family’s health is being protected. They contain a built-in stabiliser making them particularly effective in outdoor pools where chlorine loss to sunlight can be a problem.InstructionsThe product can be dosed directly into the pool without pre-dissolving. It should always be used when bathing has ceased. For outdoor use, avoid facing the wind when dosing.Calculate the volume of water in your pool (if in doubt, consult the Fi-Clor Swimming Pool Handbook). For cold water (below 20ºC) or non-circulating water, pre-dissolve in a plastic bucket uncontaminated by other chemicals (or other types of chlorine) and distribute uniformly round the pool.For more information follow the links belowProduct Brochure;http://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Data;http://www.certikin.co.uk/pdf/031%20MSDS%20Fi%20Clor%20Granules.pdf

Fi-Clor Sanitiser - Stabilised Chlorine Maxi Tablets 200gm - -  
Fi-Clor Maxi-Tabs, unrivalled in quality, are designed to slowly release a safe but highly concentrated level of available chlorine over a period of several days to combat bacteria and other pollutants. Because they contain a built-in stabiliser, they are ideal for outdoor pools where loss to sunlight can be a problem. Instructions Calculate the volume of water in your pool (if in doubt, consult the Fi-Clor Swimming Pool Handbook).Remove plastic wrapping and place the Maxi-Tabs in skimmer basket or tablet feeder.School, hotel or public pool feeder requirements will vary, depending on water capacity, water temperature, flow rate and number of bathers. Adjust dosage to maintain correct free chlorine readings.For more information follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/028%20MSDS%20Fi%20Clor%20Maxi%20Tabs.pdf

Fi-Clor Premium 5 Stabilised Chlorine Granules - -  
5 Actions in only one treatment. Fi-Clor Premium 5 Granular is specially formulated to out-perform standard chlorine granules, rapidly disinfecting water to kill potentially harmful bacteria and other organisms. It contains an algicide to tackle the problem of green water and a clarifier to keep your water crystal clear. Water balance is easier to control as the granules have little effect on pH, and the product is stabilised to combat wasteful loss of sanitiser to sunlight, making it ideal for use in outdoor pools. Instructions The product can be dosed directly into the pool without pre-dissolving. It should always be used when bathing has ceased. For outdoor use, avoid facing the wind when dosing.Calculate the volume of water in your pool (If in doubt, consult the Fi-Clor Swimming Pool Handbook).For cold water (below 20ºC) or non-circulating water, pre-dissolve in a plastic bucket uncontaminated by other chemicals (or other types of chlorine) and distribute uniformly round the pool.For more information follow the links belowProduct Brochure;http://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Data;http://www.certikin.co.uk/pdf/035%20MSDS%20Fi%20Clor%20Premium%205%20Granules.pdf

Fi-Clor Premium 5 Stabilised Chlorine Tablets 200gm - -  
5 Actions in only one treatment. Fi-Clor Premium 5 Tablets are specially formulated to out-perform standard 200g trichlor tablets, slowly releasing a powerful, long lasting disinfectant to kill potentially harmful bacteria and other organisms. Premium 5 Tablets also contain an algicide to tackle the problem of green water and a clarifier to keep your water crystal clear. The pH properties of the tablets will make it easier to balance water in hard water areas, and the product is stabilised to combat wasteful loss of sanitiser to sunlight making it ideal for use in outdoor pools. Instructions Calculate the volume of water in your pool (if in doubt, consult the Fi-Clor Swimming Pool Handbook).  Tablet dissolving rate will depend on water temperature and flow rate. Adjust dosage of PREMIUM 5 Tablets to maintain correct chlorine readings. If you need to raise free chlorine levels quickly, dose Premium 5 rapid dissolving stabilised chlorine granules by sprinkling directly into the pool in accordance with the instructions on the pack.Superchlorinate the water every 1 – 2 weeks using a stabiliser-free chlorine such as Fi-CLOR Superchlorinator. For more information, please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/052%20MSDS%20Fi%20Clor%20Premium%205%20Tablets.pdf

Fi-Clor Superfast Chlorine Granules (Stabiliser Free) 4kg Container - FISHG4 -  
KILLS WATER-BORNE BACTERIA. Fast dissolving & fast acting. No chlorine lock. Fi-Clor Superfast granular hypochlorite can be used as a regular pool sanitiser – it is especially recommended for pools that are open all year round. Superfast contains 10% more available chlorine than standard calcium hypochlorite and its fine particle size enables you to dose it directly into the pool rather than pre-dissolve. It dissolves rapidly to form active free chlorine to kill bacteria and help control algae. Superfast granules contain calcium which helps balance soft water, and it is stabiliser-free so avoiding the problem of 'chlorine lock'. Instructions For maximum efficiency stabilise the water at the beginning of the season with Fi-Clor Chlorine Stabiliser. Alternatively, use the product in conjunction with Fi-Clor Premium 5 multi-functional stabilised chlorine tablets which will give sufficient stabiliser to guarantee optimum performance after a short period of use. (Do not mix these products – dose them into the pool from separate locations e.g tablets in the skimmer, Superfast Granules dosed directly into the pool ). Test the water dailyCalculate the volume of water in your pool (if in doubt, consult the Fi-Clor Swimming Pool Handbook).The dosage may vary depending upon water conditions, circulation rate, time of day and geographical location. Broadcast the product evenly over a wide area in the deepest part of the pool. Test the water and adjust the dose as necessary.Superchlorinate the water at least every 2 weeks using 350g per 11,000 gallons (50 m3) of pool water.For more information follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/047%20MSDS%20Fi-Clor%20Superfast%20Granules.pdf

Fi-Clor Superfast Chlorine Capsules (Stabiliser Free) 4.5kg Container - FISHC4 -  
Fi-Clor Supercapsules can be used as a regular pool sanitiser - they are especially recommended for pools that are open all year round. They are enclosed in a protective plastic sleeve making them easy to handle. As the capsule dissolves, chlorine is released from each end of the sleeve. The surface area of the capsule exposed to water remains constant so, unlike normal 200g tablets, you get an even amount of chlorine going into the pool from start to finish. These calcium hypochlorite Supercapsules contain 65% available chlorine, no stabiliser (cyanuric acid) and will not contribute to chlorine lock. Each capsule weighs 300g and should last 3-5 days depending upon water conditions. Instructions to correct pH For maximum efficiency stabilise the water at the beginning of the season with Fi-Clor Chlorine Stabiliser. Alternatively, use the capsules in conjunction with Fi-Clor Premium 5 multi-functional stabilised chlorine granules which will contribute sufficient stabiliser to guarantee optimum performance after a short period of use. Do not mix these products – dose them into the pool from separate locations.Calculate the volume of water in your pool (if in doubt, consult the Fi-Clor Swimming Pool Handbook).The dosage may vary depending upon water conditions, circulation rate, time of day and geographical location. Test the water daily and adjust the dose as necessary. (THE CAPSULES SHOULD BE PLACED IN THE SKIMMER BASKET ONLY. NEVER USE THE CAPSULES IN FEEDERS OR AUTOMATIC CHLORINATORS).Do not remove the sleeve. Once all the chemical has dissolved, the plastic sleeve will float and the sleeve can then be removed from the skimmer and discarded.Superchlorinate the water every 1 to 2 weeks, with Fi-Clor Superchlorinator.For more information follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/044%20MSDS%20Fi%20Clor%20Supercapsules.pdf

Fi-Clor Superfast Chlorine Shock Granules (Stabiliser Free) 2.5kg Container - FISHG2 -  
ELIMINATES GREEN OR CLOUDY WATER. Convenient alternative to liquid chlorine. Fast dissolving & fast acting. No chlorine lock. Fi-Clor Superfast Shock contains 10% more available chlorine than standard calcium hypochlorite. Its fine particle size enables you to dose directly into the pool rather than pre-dissolve, rapidly forming free chlorine to kill algae. Superfast Shock is stabiliser-free, it breaks down 'chlorine-lock' and helps restore the effectiveness of chlorine in over-stabilised pools. It also has the effect of refracting light to produce pleasing blue water. Instructions Calculate the volume of water in your pool (if in doubt, consult the Fi-Clor Swimming Pool Handbook).Broadcast the product evenly over a wide area in the deepest part of the pool.Brush off any algae that may be clinging to pool surfaces. Run the filter for 24 hours then backwash to remove dead algae from the top of the filter media. Vacuum the pool.Any remaining haziness in the water should be removed by applying one of Fi-Clor’s water clarifiers.To help prevent a recurrence, dose the pool with one of Fi-Clor’s Algicides.Make sure free chlorine levels never fall below 1.5 mg/l (ppm) whether the pool is in use or notFor more information follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/046%20MSDS%20Fi-Clor%20Superfast%20Shock.pdf

Fi-Clor Superfast, Superchlorinator (Stabiliser Free) 1kg Container - FISHGSS -  
USE THE DAY BEFORE A POOL PARTY FOR SPARKLING CLEAR WATER. Breaks down pollutants that cause eye sting and odour. No chlorine lock. This pack contains sufficient Superfast product for 2 Superchlorinations or 1 shock dose in the average domestic swimming pool of 11,000 gallons (50m3) N.B. Use proportionately less to Superchlorinate smaller pools and use the measure provided for other applications such as dosing small above ground pools and spas. Instructions Make sure there are no bathers in the water and keep the circulation running.Check wind direction to ensure that no granules are blown back towards you.Broadcast the product evenly over a wide area in the deepest part of the pool; never through the skimmer. Superchlorination This provides a 'mini boost dose', ideal for freshening up your pool the day before a pool party, or if you are expecting heavy use.The pool should be Superchlorinated during evening hours and the filter kept running overnight.Test the water the following day. Bathing should not recommence until the free chlorine is 4.0 mg/l or below. Shock Dose This provides a 'strong shock dose', to kill algae and remove general pool pollution, particularly following a thunder storm.Adjust the pH to as near 7.2 as possible.Brush off any algae that may be clinging to pool surfaces. Run the filter for 24 hours then backwash to remove dead algae from the top of the filter media. Vacuum the pool. Any remaining haziness should be removed by applying Fi-Clor Rapid clarifier.To help prevent a recurrence, dose the pool with one of Fi-Clor’s Algicides.Make sure free chlorine levels never fall below 1.5 mg/l (ppm) whether the pool is in use or notFor more information follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/045%20MSDS%20Fi-Clor%20Superfast%20Superchlorinator.pdf

Fi-Clor Superfast, Superchlorinator (Stabiliser Free) 450g Container - FISHSC -  
USE THE DAY BEFORE A POOL PARTY FOR SPARKLING CLEAR WATER. Breaks down pollutants that cause eye sting and odour. No chlorine lock. This pack contains sufficient Superfast product for 1 Superchlorination in the average domestic swimming pool of 11,000 gallons (50m3). N.B. Use proportionately less to Superchlorinate smaller pools and use the measure provided for other applications such as dosing small above ground pools and spas.For more information follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdf Safety Datahttp://www.certikin.co.uk/pdf/045%20MSDS%20Fi-Clor%20Superfast%20Superchlorinator.pdf

Fi-Clor Chlorine & Bromine Reducer 2.5kg Container - FICBR -  
Fi-Clor Chlorine/Bromine Reducer neutralises high levels of chlorine or bromine in pool or spa water. Ideal treatment when chlorine or bromine levels are higher than recommended for bathing, and there is insufficient time for them to fall naturally. Instructions Accurately measure the free available chlorine level or available bromine and calculate the amount of sanitiser that needs to be reducedFor pools on chlorine, the dose rate is 7 grams of  Fi-Clor Chlorine/Bromine Reducer per 1m3 of water  for every 1ppm (mg/l) of chlorine to be reduced. For the average sized home pool of 50m3 (11,000 gallons), 350g of the product will reduce the chlorine level by 1ppm (mg/l).For pools on bromine, the dose rate is 3 grams of  Fi-Clor Chlorine/Bromine Reducer per 1m3 of water  for every 1ppm (mg/l) of bromine to be reduced. For the average sized home pool of 50m3 (11,000 gallons), 150g of the product will reduce the bromine level by 1ppm (mg/l).For best results, pre-dissolve in a clean plastic pail  and distribute the product evenly around the pool.Wait for at least 2 hours before re-testing, making further additions if required. Under-dose rather than  over-dose, as this can produce an unwanted chlorine/ bromine demand. Caution Never mix in their solid state, or in concentrated solution, Fi-Clor BLUE and RED label products.For more information please follow the link belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdf

Cleaning & Maintenance

Certikin Floating Vacuum Hose - -  
For commercial or private pools, the CX hose is available in the following lengths.  It is suitable for all climates and used extensively worldwide.38mm (1.5")9 metre (CX9)12 metre (CX12)15 metre (CX15)18 metre (CX18)25metre (CX25)36 metre - cuffed 1.5" (FLX150/36)Also available in,50mm (2") 20 metre length (CX20/2)You may also need a Certikin Cornea Vacuum Plate (HD103) which fits over your skimmer bowl (return to Cleaning & Maintenance main menu for more information and image)TOP TIPWhy not purchase a strap and hanger for your new Certikin Vacuum Hose and keep your pool house tidy, one size fits all vacuum hoses. (SPC545)     

Certikin Cornea Vacuum Plate - HD103 -  
Attaches to your skimmer bowl (basket may have to be removed) and then attach your vacuum hose to the hosetail (see image)

Certikin Vacuum Head for Liner & Concrete Pools - HD70LN -  
Designed specifically for use in liner pools but suitable for cleaning concrete pools. The HD70L incorporates a flow control valve, hard wearing bristles and a clear see-through body. It is supplied with an 1.5" vacuum hose nozzle.1.25" nozzles are available upon request.

Certikin 12" Flexible Vacuum Head for Concrete Pools - HD70 -  
Features of the HD70 include a unique flexible body withencapsulated wheels, an extra long nozzle for 1.5" vacuumhose, vent holes and attractive design

Certikin 19" Plastic Vacuum Head For Concrete Pools - CVH19 -  
Certikin 19" (483mm) Plastic Vacuum Head for Concrete Pools

Bendervac 18" Vacuum Head For Concrete Pools - BE18 -  
The Bendervac 18" (450mm) Vacuum Head is suitable for cleaning concrete pools.

Certikin 18" Deluxe Pool Brush - Aluminium Handle - RA902 -  
18" (450mm) deluxe brush - aluminium handleFour rows of superior nylon bristle on a tough shaped polypropylene stock give the RA902 the edge over all other brushes on the market. Guaranteed to give many years of service and not to be compared with cheaper alternatives

Certikin 18" Pool Brush - HD66 -  
Certikin 18" (450mm) pool brushFour rows of superior nylon bristle on a tough shaped polypropylene stock give the HD66 the edge over all other brushes on the market. Guaranteed to give many years of service and not to be compared with cheaper alternatives

Certikin 36" Commercial Pool Brush - RA908 -  
36" (900mm) commercial brush

Certikin 6" Algea Brush - HD69 -  
Specially designed swivel head for easy cleaning of walls and floors. The high quality stainless steel bristles are ideal for removing algae from pool wall surfaces.

Certikin Flat Leaf Net - HD67 -  
Very durable frame and integral Pine-mesh net for removing floating debris on the surface of your pool.

Certikin Deep Leaf Net - HD68 -  
Virtually unbreakable frame with moulded-in net andscoop for cleaning the bottom of the pool

Rainbow In Line Leaf Trap - RA179 -  
Features snap open and close lid, clear housing and large handle for ease of carrying. Traps debris in polyester bag. Includes One 3 Foot Hose.

Certikin Telescopic Handles - -  
The grip lock mechanism enables easy adjustment of pole length and the comfortable hand grip makes use of the Certikin poles a real pleasure. The poles are designed for use with any of the Certikin accessories as well as those manufactured by others. Available in three sizes,4'–8' (1.22–2.44m) CK486'–12' (1.83–3.66m) CK6128'–16' (2.44–4.88m) CK816TOP TIPWhy not purchase a couple of plastic hangers for your new Certikin Telescopic Pole to keep your pool area tidy CCM077 (no image available)

Certikin Commercial Handle 8ft to 24ft - CKC8N -  
Supplied in 8' (2.44m) lengths, the poles may be joined together to achieve a length of up to 24'.

Graphite 10" Scope Thermometer - CCMG69 -  
A choice of three thermometers with a string for securing to ladder or handrail, all very easy to read in either Celsius or Fahrenheit.

Floating Thermometer - CCM202 -  
A choice of three thermometers with a string for securing to ladder or handrail, all very easy to read in either Celsius or Fahrenheit

Chrome on Brass Deluxe Thermometer - CK82 -  
A choice of three thermometers with a string for securing to ladder or handrail, all very easy to read in either Celsius or Fahrenheit

Backwash Hose (Red) - -  
Available in 50' or 100' lengthsTOP TIPDon't forget to order a Jubilee Clip to secure the hose to the Backwash outlet on your filter

Heat Pumps,Summer Heating, Single Phase

Calorex Compact Heat Pumps - -  
Efficiency and reliabilityThe 29 range consists of two single phase models, 8.8 kW and 12kW. Their compact form is aesthetically pleasing, they can be placed discretely in the pool area or sited in a plant room.  These models are elegant and simple to use.  Just set the thermostat to ensure fully automatic operation throughout the season.The advantages:✓ Extremely quiet✓ Titanium heat exchanger compatible with all types of water treatment✓ Digital thermostat✓ Flexible Installation✓ Totally automatic operation✓ Ecologically sound and economic to runFor more information on Heat Pumps, follow the link below;http://www.certikin.co.uk/pdf/Heatpumps2009.pdf

Calorex Premium Heat Pumps - -  
The Premium 31 range is specifically designed for heating swimming pools with the option of swimming for a longer season.A complete range for private swimming pools.  This comprehensive range of high quality units, producing up to 21 kilowatts, is suitable for both the leisure industry and private pools. The Premium 31 range is suitable for “All Seasons” operating in temperatures below 0°C and can be used to heat both indoor and outdoor pools.Our products are the only ones on the market to incorporate sound and heat insulation of the inner panels therefore making them extremely quiet.The advantages:✓ Heats spas and swimming pools up to 35°C✓ All models are available in three phase✓ All components are installed inside the machine to enhance visual impact✓ Fitted with a Titanium heat exchanger -  compatible with all types of water treatment             ✓ Eco friendly and economic to run✓ Simple to use✓ Automatic controls and operation✓ Water flow switch with flow status indicationFor more information follow the link belowhttp://www.certikin.co.uk/pdf/Heatpumps2009.pdf

Lacron Filters

Lacron Side Mount Filter - -  
Crystal clear, sparkling water is the most important feature of any swimming pool. A filter is by far the most efficient way to ensure perfect water quality for many years to come. Certikin filters can be used with standard Certikin 16/30-grade silica sand.The Certikin Lacron range is designed to cater for all residential applications from small above ground pools, through to larger in ground domestic installations30 year proven trackrecordPressure tested to 60 psi (4 bar)Manufactured from the highest-grade materialsHi gloss, non corrosive, FRP tank and base componentsNine-Inch, Clear view, easy access, service lidEnergy efficient collection and distribution pipe-workSpeed style installation and service connectionsEasy access winter drain tapTOP TIPDon't forget to order your valve connecting pipe set and filter media for the relevant size filter. Call Sarah or Charmaine at our office for further details and prices 01440 713355For more information follow the link belowhttp://www.certikin.co.uk/pdf/Lacron%281%29.pdf

Lacron Top Mount Filter - -  
Crystal clear, sparkling water is the most important feature of any swimming pool. A filter is by far the most efficient way to ensure perfect water quality for many years to come. Certikin filters can be used with standard Certikin 16/30-grade silica sand.The Certikin Lacron range is designed to cater for all residential applications from small above ground pools, through to larger in ground domestic installations30 year proven track recordPressure tested to 60 psi (4 bar)Manufactured from the highest-grade materialsHi gloss, non corrosive, FRP tank and base componentsNine-Inch, Clear view, easy access, service lidEnergy efficient collection and distribution pipe-workSpeed style installation and service connectionsEasy access winter drain tapTOP TIPDon't forget to order your filter media for the relevant size filter.Call Sarah or Charmaine at our office for further details and prices 01440 713355For more information follow the link belowhttp://www.certikin.co.uk/pdf/Lacron%281%29.pdf

Liner Patterns

Astino - -  

Coral - -  

Granite - -  

Estoril - -  

Byzanze - -  

Marble - -  

Mosaic - -  

Ice Blue - -  

Aqua - -  

Black - -  

White - -  

Sand - -  

Blue - -  

Safety Covers

Coverstar Automatic Safety Cover - coverstar5 -  
The Coverstar automatic pool cover can accommodate almost any shape or style of swimming pool.  The options range from straight forward retro-fit systems for existing pools to fully incorporated, underguide, pit mounted systems for new pools.   The Coverstar system has been developed through many years of innovative design, precision engineering and quality production.    Safety - Children are most at risk in their own back garden, when parents believe they are safely in the house.  A safety pool cover is considered the number one safety feature you can have on your pool.   The Coverstar systems provide safety and piece of mind.  They seal the entrance to the pool with reinforced fabrics and extensively tested automatic mechanisms.   Evaporation & Heat Loss - During the day Coverstar's fabric absorbs solar energy and thermally conducts it to the cooler water below.  At night it helps to eliminate evaporation and insulates your pool.  This combination will considerably reduce the running costs of your pool.   Maintenance - Your pool will remain much cleaner with a Coverstar cover in place.  Since the Coverstar is so easy to use it can be in place whenever the pool is not in use, thus sealing dirt and debris.  The Coverstar is the best maintenance partner you can have and ensures a clean and enjoyable pool environment.   Features - Hydraulic motor drive systems allows electric's to be installed a safe distance from the pool Simple and safe key operation Cover material manufactured in Ultraguard (TM) industrial grade fabric developed exclusively for Coverstar Coverstar is available in eight colours Prefabricated roller pit available Installation can be arranged.For more information follow the link belowhttp://www.certikin.co.uk/pdf/coverstar2007.pdfFor more information, please call our office and speak to Sarah or Charmaine about details and prices 01440 713355

Walu Safety Cover - -  
The Walu Safety cover is a true all-year-round cover and is ideal for use as a winter cover. Each panel of the cover has a series of integrated drain holes which allow rain water to seep through, but will not allow debris to enter the pool.  The anti-abrasion fabric is tough and easy to clean and every cover comes with high wind anchors as standard. Available in two styles to cover almost any pool, the Walu is an excellent winter cover that also provides the peace of mind of being a fully certified (NF P 90-308) safety cover.Features• Manufactured to French NF standard - weight capacity of 100kg (approximately 220lbs)• Exclusive changeable panel system• Adjustable, lockable anchor points• Complete with crank handle - can be operated from either side• Shaping for steps and ladders available• Quick and easy to install and operate• The Walu safety cover is available in a variety of coloursFor more information please follow the link belowhttp://www.certikin.co.uk/pdf/WALU-INFO.pdf

Walu Woodstar Above Ground Pool Safety Cover - -  
 A sister product to the successful Walu Safety Cover, the Woodstar is specifically designed to offer the same level of safety (conforms to French standard NF P 90-308) and simplicity for timber above ground pools. Secured with ratchets on pre-angled brackets and rolled with a convenient hand-wheel, the Woodstar is easy to install and operate.Available in a range of colours, the Woodstar removes the need for any other cover or roller system on your above ground pool, and to make it that perfect fit, cut outs (at the end of the pool) for ladder entry points, filtration systems and counter current devices can be included.Price is per m², based on largest length and widthFor more information, please call our office and speak to Sarah or Charmaine for further details and prices 01440 713355

Sta-Rite Pumps

Sta-Rite Pump - -  
Sta-Rite 5P2R Series pumps are precision moulded, fibreglass reinforced, temperature and corrosion resistant.  They are lightweight, exceptionally strong thermoplastic and are designed for much higher pressure operation."See Thru" trap lidEliminates all the guesswork.  You can see when the basket needs cleaning.  Exclusive "lock-in" 5" basket prevents large debris from clogging impeller.Heavy Duty Motor50 Hz motors are designed for continuous, quiet operation.  They feature a stainless steel one piece shaft, sealed and permanently lubricated bearings which promotes cooler running for prolonged life under high ambient conditions.For more information please follow the link belowhttp://www.starite.de/download/sta_rite_2005_catalogue.pdf

Alkorplan On Site Welded Liners

Mosiac - -  

Marble - -  

Byzance - -  

Persia Sand - -  
P

Carrara - -  

Mid Blue - -  

Ice Blue - -  

Aqua - -  

Grey - -  

Black - -  

Sand - -  

White - -  

Aquaspeed Pumps

Aquaspeed Single Phase Pump - -  
The Certikin Aquaspeed is suitable for both pool and spa filtration applications. Completely self priming it is available in a wide range of sizes from 0.5HP to 3.5HP (in both single and three phase versions) and is suitable for salt-water pools. A 2 speed 1.5HP (1.1kW) single phase version is also available. A single pump range covering all sizes from 0.5HP to 3.5HPLarge capacity strainer basketHigh pressure screwfit lid for ease of useTEFC motor IP55 rated and fully CE approvedSupplied with quick coupling unions For more information please follow the link belowhttp://www.certikin.co.uk/pdf/aquaspeed.pdf

Aquaspeed Three Phase Pumps - -  
The Certikin Aquaspeed is suitable for both pool and spa filtration applications. Completely self priming it is available in a wide range of sizes from 0.5HP to 3.5HP (in both single and three phase versions) and is suitable for salt-water pools. A 2 speed 1.5HP (1.1kW) single phase version is also available. A single pump range covering all sizes from 0.5HP to 3.5HPLarge capacity strainer basketHigh pressure screwfit lid for ease of useTEFC motor IP55 rated and fully CE approvedSupplied with quick coupling unionsFor more information please follow the link belowhttp://www.certikin.co.uk/pdf/aquaspeed.pdf

Gas Fired Heaters

Certikin Natural Gas Heaters 055 Range - -  
Fully CE approved by British Gas in the UKElectronic Ignition Strong, weatherproof, powder coated casing suitable for indoor or outdoor installation High operational efficiency Natural gas and LP models available44,000 BTU input (larger sizes also available) Supplied with pre-wired 13 amp plug and lead Suitable for Natural or LP gas EconTherm Heat ExchangerThe heater is equipped with a unique all-copper finned tube heat exchanger, designed for efficient heat transfer. The header casting is made of cast iron, durable and corrosion resistant.Please note: Copper finned heat exchangers are not suitable for use with salt water.UniTherm Flow SystemThe heater is equipped with the advanced Unitherm Plus Full Flow system which controls both water temperature and flow rate inside the heater. However if required for use with pools a bypass should be used to control water flow.Longer lasting tough exteriorThe exterior polyester coating is a non-polluting synthetic material that’s applied electrostatically in powder form, then melted and fused into a smooth, hard coating in baking ovens. That means no cracking, scratching, peeling or fading. You can count on a long-lasting, lustrous protective finish that lasts years longer than ordinary painted or baked enamel finishes.Cost and Energy Efficient The MB 055 heater from Certikin does not require heat sinks because the alumina silica combustion chamber does not retain heat when the heater shuts off. Energy smart Certikin heaters consistently achieve high efficiency ratings.  With many years of experience in designing, engineering, and manufacturing all types of residential and commercial pool, space, and hot water heaters, Certikin’s swimming pool gas heaters are simply the best.For more information follow the link belowhttp://www.certikin.co.uk/pdf/gas055.pdf

Certikin Natural Gas Heaters 105 Range - -  
Electronic Ignition gives highly reliable performanceStrong, weatherproof, powder coated casing suitable for indoor or outdoor installationPatented highly efficient heat exchangerSupplied with pre-wired 13 amp plug and leadSuitable for natural or LP gasFully CE approved for most european countriesEconTherm Heat ExchangerThe MB range is equipped with a unique all-copper finned tube heat exchanger, designed for efficient heat transfer. Both header castings are made of cast iron, durable and corrosion resistant.Please note: Copper finned heat exchangers are not suitable for use with salt water.UniTherm Flow SystemThe MB105 and MB155 heaters are equipped with the advanced Unitherm Plus Full Flow system which controls both water temperature and flow rate inside the heater thus reducing condensation, soot and scale buildup.Longer lasting tough exteriorThe MB range’s exterior polyester coating is a non-polluting synthetic material that’s applied electrostatically in powder form. That means no cracking, scratching, peeling or fading.  You can count on a long-lasting, lustrous protective finish that lasts years.Cost and energy efficientThe range of MB 105/155 heaters from Certikin spare you the costly installation of heat sinks because the alumina silica combustion chamber does not retain heat when the heater shuts off. Energy smart Certikin heaters consistently achieve high efficiency ratings. Simply the bestThe Certikin MB105/155 heaters with EconoTherm heat exchangers and UniTherm Plus systemlast longer and deliver more heat to your pool or spa water, per unit of fuel, than any other heaters you can buy.  With many years of experience in designing, engineering, and manufacturing all types of residential and commercial pool, space, and hot water heaters, Certikin’s swimming pool gas heaters are simply the best.For more information follow the link belowhttp://www.certikin.co.uk/pdf/105.gasheater.lft.x4.pdf

Certikin Natural Gas Heaters 155 Range - -  
Electronic Ignition gives highly reliable performanceStrong, weatherproof, powder coated casing suitable for indoor or outdoor installationPatented highly efficient heat exchangerSupplied with pre-wired 13 amp plug and leadSuitable for natural or LP gasFully CE approved for most european countriesEconTherm Heat ExchangerThe MB range is equipped with a unique all-copper finned tube heat exchanger, designed for efficient heat transfer. Both header castings are made of cast iron, durable and corrosion resistant.Please note: Copper finned heat exchangers are not suitable for use with salt water.UniTherm Flow SystemThe MB105 and MB155 heaters are equipped with the advanced Unitherm Plus Full Flow system which controls both water temperature and flow rate inside the heater thus reducing condensation, soot and scale buildup.Longer lasting tough exteriorThe MB range’s exterior polyester coating is a non-polluting synthetic material that’s applied electrostatically in powder form. That means no cracking, scratching, peeling or fading.  You can count on a long-lasting, lustrous protective finish that lasts years.Cost and energy efficientThe range of MB 105/155 heaters from Certikin spare you the costly installation of heat sinks because the alumina silica combustion chamber does not retain heat when the heater shuts off. Energy smart Certikin heaters consistently achieve high efficiency ratings. Simply the bestThe Certikin MB105/155 heaters with EconoTherm heat exchangers and UniTherm Plus systemlast longer and deliver more heat to your pool or spa water, per unit of fuel, than any other heaters you can buy.  With many years of experience in designing, engineering, and manufacturing all types of residential and commercial pool, space, and hot water heaters, Certikin’s swimming pool gas heaters are simply the best.For more information follow the link belowhttp://www.certikin.co.uk/pdf/105.gasheater.lft.x4.pdf

Certikin Natural Gas Heaters, 185 Range - -  
Electronic Ignition guarantees highly reliable performanceStrong, weatherproof, powder coated casing suitable for indoor or outdoor installationSupplied with prewired 13 amp plug and leadLarge, clear, accurate, digital pool temperature displaySuitable for natural or LP gasFully CE approved for most European countriesSmart function. Smart form.One look will tell you that the Certikin MB range is different. Sleek, contemporary, state of-the-art, inside and out. The unique venting design and electronic ignition helps to ensure effortless and uninterrupted performance regardless of wind conditions.Longer lasting tough exteriorThe MB range’s exterior polyester coating is a non-polluting material. You can count on a long-lasting, lustrous protective finish that lasts years. Whatever the weather Performance and reliability are further enhanced by Certikin’s outdoor stackless top designed to keep the MB 185/265/405 operational even in windy conditions and downdraughts.Advanced UniTherm Plus full-flow system improves heater lifeCondensation-free operation is assured even with low temperature inlet water. Both water temperature and flow rate inside the heater are controlled to reduce condensation, sooting and scale build-up that can shorten heater life.EconTherm Heat ExchangerThe MB range is equipped with a unique all-copper finned tube heat exchanger, designed for efficient heat transfer. Models 185, 265 and 405 feature all Capron headers.Please note: Copper finned heat exchangers are not suitable for use with salt water.For more information follow the link belowhttp://www.certikin.co.uk/pdf/Gas-heater6-page-0276.pdfFor MB265 (244,000 BTU, 71.51KW) and MB405 (370,000 BTU, 108.44KW) range of Heaters Please call Sarah or Charmaine for cost and further details 01440 713355.

Certikin Propane Gas Heaters 055 Range - -  
Fully CE approved by British Gas in the UKElectronic Ignition Strong, weatherproof, powder coated casing suitable for indoor or outdoor installation High operational efficiency Natural gas and LP models available44,000 BTU input (larger sizes also available) Supplied with pre-wired 13 amp plug and lead Suitable for Natural or LP gas EconTherm Heat ExchangerThe heater is equipped with a unique all-copper finned tube heat exchanger, designed for efficient heat transfer. The header casting is made of cast iron, durable and corrosion resistant.Please note: Copper finned heat exchangers are not suitable for use with salt water.UniTherm Flow SystemThe heater is equipped with the advanced Unitherm Plus Full Flow system which controls both water temperature and flow rate inside the heater. However if required for use with pools a bypass should be used to control water flow.Longer lasting tough exteriorThe exterior polyester coating is a non-polluting synthetic material that’s applied electrostatically in powder form, then melted and fused into a smooth, hard coating in baking ovens. That means no cracking, scratching, peeling or fading. You can count on a long-lasting, lustrous protective finish that lasts years longer than ordinary painted or baked enamel finishes.Cost and Energy Efficient The MB 055 heater from Certikin does not require heat sinks because the alumina silica combustion chamber does not retain heat when the heater shuts off. Energy smart Certikin heaters consistently achieve high efficiency ratings.  With many years of experience in designing, engineering, and manufacturing all types of residential and commercial pool, space, and hot water heaters, Certikin’s swimming pool gas heaters are simply the best.For more information follow the link belowhttp://www.certikin.co.uk/pdf/gas055.pdf

Certikin Propane Gas Heaters 105 Range - -  
Electronic Ignition gives highly reliable performanceStrong, weatherproof, powder coated casing suitable for indoor or outdoor installationPatented highly efficient heat exchangerSupplied with pre-wired 13 amp plug and leadSuitable for natural or LP gasFully CE approved for most european countriesEconTherm Heat ExchangerThe MB range is equipped with a unique all-copper finned tube heat exchanger, designed for efficient heat transfer. Both header castings are made of cast iron, durable and corrosion resistant.Please note: Copper finned heat exchangers are not suitable for use with salt water.UniTherm Flow SystemThe MB105 and MB155 heaters are equipped with the advanced Unitherm Plus Full Flow system which controls both water temperature and flow rate inside the heater thus reducing condensation, soot and scale buildup.Longer lasting tough exteriorThe MB range’s exterior polyester coating is a non-polluting synthetic material that’s applied electrostatically in powder form. That means no cracking, scratching, peeling or fading.  You can count on a long-lasting, lustrous protective finish that lasts years.Cost and energy efficientThe range of MB 105/155 heaters from Certikin spare you the costly installation of heat sinks because the alumina silica combustion chamber does not retain heat when the heater shuts off. Energy smart Certikin heaters consistently achieve high efficiency ratings. Simply the bestThe Certikin MB105/155 heaters with EconoTherm heat exchangers and UniTherm Plus systemlast longer and deliver more heat to your pool or spa water, per unit of fuel, than any other heaters you can buy.  With many years of experience in designing, engineering, and manufacturing all types of residential and commercial pool, space, and hot water heaters, Certikin’s swimming pool gas heaters are simply the best.For more information follow the link belowhttp://www.certikin.co.uk/pdf/105.gasheater.lft.x4.pdf

Certikin Propane Gas Heaters 155 Range - -  
Electronic Ignition gives highly reliable performanceStrong, weatherproof, powder coated casing suitable for indoor or outdoor installationPatented highly efficient heat exchangerSupplied with pre-wired 13 amp plug and leadSuitable for natural or LP gasFully CE approved for most european countriesEconTherm Heat ExchangerThe MB range is equipped with a unique all-copper finned tube heat exchanger, designed for efficient heat transfer. Both header castings are made of cast iron, durable and corrosion resistant.Please note: Copper finned heat exchangers are not suitable for use with salt water.UniTherm Flow SystemThe MB105 and MB155 heaters are equipped with the advanced Unitherm Plus Full Flow system which controls both water temperature and flow rate inside the heater thus reducing condensation, soot and scale buildup.Longer lasting tough exteriorThe MB range’s exterior polyester coating is a non-polluting synthetic material that’s applied electrostatically in powder form. That means no cracking, scratching, peeling or fading.  You can count on a long-lasting, lustrous protective finish that lasts years.Cost and energy efficientThe range of MB 105/155 heaters from Certikin spare you the costly installation of heat sinks because the alumina silica combustion chamber does not retain heat when the heater shuts off. Energy smart Certikin heaters consistently achieve high efficiency ratings. Simply the bestThe Certikin MB105/155 heaters with EconoTherm heat exchangers and UniTherm Plus systemlast longer and deliver more heat to your pool or spa water, per unit of fuel, than any other heaters you can buy.  With many years of experience in designing, engineering, and manufacturing all types of residential and commercial pool, space, and hot water heaters, Certikin’s swimming pool gas heaters are simply the best.For more information follow the link belowhttp://www.certikin.co.uk/pdf/105.gasheater.lft.x4.pdf

Certikin Propane Gas Heaters 185 Range - -  
* Electronic Ignition guarantees highly reliable performance    * Strong, weatherproof, powder coated casing suitable for indoor or outdoor installation    * Supplied with prewired 13 amp plug and lead    * Large, clear, accurate, digital pool temperature display    * Suitable for natural or LP gas    * Fully CE approved for most European countriesSmart function. Smart form.One look will tell you that the Certikin MB range is different. Sleek, contemporary, state of-the-art, inside and out. The unique venting design and electronic ignition helps to ensure effortless and uninterrupted performance regardless of wind conditions.Longer lasting tough exteriorThe MB range’s exterior polyester coating is a non-polluting material. You can count on a long-lasting, lustrous protective finish that lasts years. Whatever the weather Performance and reliability are further enhanced by Certikin’s outdoor stackless top designed to keep theMB 185/265/405 operational even in windy conditions and downdraughts.Advanced UniTherm Plus full-flow system improves heater lifeCondensation-free operation is assured even with low temperature inlet water. Both water temperature and flow rate inside the heater are controlled to reduce condensation, sooting and scale build-up that can shorten heater life.EconTherm Heat ExchangerThe MB range is equipped with a unique all-copper finned tube heat exchanger, designed for efficient heat transfer. Models 185, 265 and 405 feature all Capron headers.Please note: Copper finned heat exchangers are not suitable for use with salt water.For more information follow the link belowhttp://www.certikin.co.uk/pdf/Gas-heater6-page-0276.pdfFor MB265 (244,000 BTU, 71.51KW) and MB405 (370,000 BTU, 108.44KW) range of Heaters Please call Sarah or Charmaine for cost and further details 01440 713355.

Liner Tilebands

Cadiz - -  

Ibiza Blue - -  

Keops Blue - -  

Cordoba - -  

Sevilla - -  

Catalan - -  

Byzanze - -  

Mosaic - -  

Andalucia - -  

Summer Solar Covers

- -  

- -  

HPS Hydroswim Pumps

HPS Hydroswim Pumps Single Phase - -  
Self-priming centrifugal pumps for swimming pool filtration.FeaturesHigh hydraulic efficiencyUltra quiet operationSimple, robust & compactOne-piece body in durable resistant composite materialNoryl impellorInnovative design with patented strainer basketUse: fresh water - sea water - treated water - brackish waterFast-opening translucent lidMotor IP 55 - class F - continuous ratingStainless steel shaftFor more information please follow the link belowhttp://www.certikin.co.uk/pdf/HPS.pump.pdf

Liner Motifs & Logos

Oil Fired Heaters

Certikin Oil Fired Heaters - -  
FeaturesEasy to use diagnostic electronic controls with LED displayFully tested and approved to OFTEC and EC standardsComplies with section L 2002 Building RegulationsSuitable for use on salt water poolsUK based technical expertiseDesigned to run with high efficiency, clean combustion and low noise levelPre-plumbed and pre-wired for ease of installationAll Models fitted with Riello burnersOptional balanced flue kits, left, right or rear available for all models (28 sec Kerosene only)Optional vertical balanced flue (no ventilation required)Optional outdoor installation kitSPCOHMIK - Multiple pool heater load share option. Kit requiredControlsA state of the art electronic control panel created specially for oil pool heating and central heatingapplications which is easy to use and includes an accurate display of pool temperature. The diagnostic control panel includes a pressure gauge and LED lights to indicate everything from the boiler being turned on to burner lockout.Four accurate thermostats control the pool water temperature, the boiler temperature, the safety high limit and the automatic by-pass (not fixed). Condensation inside the water jacket is minimised to maximise the operating life of the boiler.PlumbingThe heater comes complete, pre-plumbed and pressure tested resulting in ease of installation and peace of mind for the customer. A high efficiency counterflow water to water heat exchanger is used for pool water heating. System inhibitor is supplied with every heater.For more information follow the link belowhttp://www.certikin.co.uk/pdf/a4-leaflet-new.pdf

Summer Solar Cover Roller

- -  

- -  

Non Chlorine

Fi-Clor Non Chlorine Shock 5kg Container - FINCS -  
Fi-Clor Non-Chlorine Shock can be used to shock dose pools which use all types of chlorine as a sanitiser without boosting chlorine levels. It may also be used for reactivating spent Bromine in Bromine treated pools. It dissolves rapidly to break down unpleasant pollutants and organic matter, and is effective over a wide range of water conditions and pH values. It is an ideal shock treatment for pools using automatic pool covers. Instructions The product can be dosed directly into the pool  without pre-dissolving. It should always be used when bathing has ceased. For outdoor use, avoid facing the wind when dosing.Calculate the volume of water in your pool (if in doubt, consult the Fi-Clor Swimming Pool Handbook). To shock dose, the rate is 750g of Non-Chlorine Shock to 50m3 (11,000 gallons) of water. To treat green  or cloudy water, add 1kg to 50m3 (11,000 gallons).Treat immediately at the onset of green or cloudy water. [Note: Where algae infestation is at an advanced stage, you are recommended to use Fi-Clor  Superfast Shock].Dose into an area of the pool where there is good  water circulation CAUTION Never mix in their solid state, or in concentrated solution,   Fi-Clor BLUE and RED label products.For more information follow the links belowProduct Brochurehttp://www.fi-clor.co.uk/nonchlorine_shock.shtmlSafety Datahttp://www.certikin.co.uk/pdf/043%20MSDS%20Fi-Clor%20Chlorine-Free%20Shock.pdf

Vision Filters

Vision Side Mounted Filter - -  
The Certikin Vision range of domestic bobbin wound filters embody the latest in fibreglass winding technology. Providing a strong and durable tank with an impressive 10 year warranty.The awesome 10” diameter lid on both the top and side mount models makes servicing and maintenance quicker and easier, and a hydraulically balanced lateral system ensures optimum flow characteristics during filtration and backwashingFeaturesFull 10 year tank warranty10” lid and lock ring assemblyPatented clear top mount valve ring - allows users to view filter in action whilst the pump is runningHydraulically designed lateral arrangementDual water and media dump port arrangementImperial and metric quick connect unionsSupplied complete with 6-way multiport valve, air relief and pressure gaugeTOP TIPDon't forget to order your filter media for the relevant size filter. Call Sarah or Charmaine at our office for further details and prices 01440 713355For more information please follow the link belowhttp://www.certikin.co.uk/pdf/visionfilter.pdf

Vision Top Mounted Filters - -  
The Certikin Vision range of domestic bobbin wound filters embody the latest in fibreglass winding technology. Providing a strong and durable tank with an impressive 10 year warranty.The awesome 10” diameter lid on both the top and side mount models makes servicing and maintenance quicker and easier, and a hydraulically balanced lateral system ensures optimum flow characteristics during filtration and backwashingFeaturesFull 10 year tank warranty10” lid and lock ring assemblyPatented clear top mount valve ring - allows users to view filter in action whilst the pump is runningHydraulically designed lateral arrangementDual water and media dump port arrangementImperial and metric quick connect unionsSupplied complete with 6-way multiport valve, air relief and pressure gaugeTOP TIPDon't forget to order your filter media for the relevant size filter. Call Sarah or Charmaine at our office for further details and prices 01440 713355For more information please follow the link belowhttp://www.certikin.co.uk/pdf/visionfilter.pdf

Winter Debris Covers

Certikin Maple Winter Debris Cover - -  
Certikin Winter Debris Covers should form an essential part of the pool winterisation process. Designed to keep the pool clear of leaves and other debris, but allow rain water through, they will also reduce the risk of frost damage. Almost any shape and size of pool can be accommodated, including shaping for roman steps and ladder entry points, - the standard design allows a 0.3m (1') overlap all around the pool. All winter covers are stitched with anti-rot thread and have anti-abrasion strips and pvc reinforcement affixed at potentially high wear areas. Polished stainless steel spring fixings and a storage bag are supplied as standard.FeaturesHighest quality woven polyethylene fabricPolished stainless steel spring fixings3 styles of traditional cover to choose from Available in a choice of colours Cover almost any pool shape and size 5 year guaranteeMaple Made from woven polyethylene with reinforced corners, anti-chaffing strips and stainless steel fixings at approximately 1.2-1.5m centres.For more information please follow the link belowhttp://www.certikin.co.uk/pdf/wintercovers-lft.pdf If you require a cover size that isn't listed below, please call Sarah or Charmaine at our office for further details and prices on 01440 713355

Certikin Criss Cross Winter Debris Cover - -  
Certikin Winter Debris Covers should form an essential part of the pool winterisation process. Designed to keep the pool clear of leaves and other debris, but allow rain water through, they will also reduce the risk of frost damage. Almost any shape and size of pool can be accommodated, including shaping for roman steps and ladder entry points, - the standard design allows a 0.3m (1') overlap all around the pool. All winter covers are stitched with anti-rot thread and have anti-abrasion strips and pvc reinforcement affixed at potentially high wear areas. Polished stainless steel spring fixings and a storage bag are supplied as standard.Features    * Highest quality woven polyethylene fabric    * Polished stainless steel spring fixings    * 3 styles of traditional cover to choose from    * Available in a choice of colours    * Cover almost any pool shape and size    * 5 year guarantee Criss Cross Made from woven polyethylene with reinforced corners, anti-chaffing strips and stainless steel fixings at approximately 1.2-1.5m centres. Includes webbing straps stitched across the full length and width of the cover for extra strength.Accu-Tab system delivers crystal clear water with minimum hassle High Reliability, low maintenance system Consistent, effective and accurate chlorine delivery Accu-Tab does not contain cyanuric acid (sunlight stabiliser) Accu-Tab is sold only through authorised dealers, contact Certichem Water Treatment for further information Accu-Tab Powerbase chlorination units are manufactured in the UK Accu-Tab 3" Blue SI calcium hypochlorite tablets are designed for use in Accu-Tab chlorinators. Tablets contain scale inhibitor and are 65% minimum available chlorine --> For more information, please follow the link belowhttp://www.certikin.co.uk/pdf/wintercovers-lft.pdfIf you require a cover size that isn't listed below, please call Sarah or Charmaine at our office for further details and prices on 01440 713355

Certikin Cedar Winter Debris Cover - -  
Certikin Winter Debris Covers should form an essential part of the pool winterisation process. Designed to keep the pool clear of leaves and other debris, but allow rain water through, they will also reduce the risk of frost damage. Almost any shape and size of pool can be accommodated, including shaping for roman steps and ladder entry points, - the standard design allows a 0.3m (1') overlap all around the pool. All winter covers are stitched with anti-rot thread and have anti-abrasion strips and pvc reinforcement affixed at potentially high wear areas. Polished stainless steel spring fixings and a storage bag are supplied as standard.Features    * Highest quality woven polyethylene fabric    * Polished stainless steel spring fixings    * 3 styles of traditional cover to choose from    * Available in a choice of colours    * Cover almost any pool shape and size    * 5 year guaranteeCedar - Made from woven polyethylene with reinforced corners, anti-chaffing strips and stainless steel fixings at approximately 1.2-1.5m centres. Includes a tough PVC skirt stitched to the underside of perimeter and fixings at approximately 1m centres.For more information, please follow the link belowhttp://www.certikin.co.uk/pdf/wintercovers-lft.pdfIf you require a cover size that isn't listed below, please call Sarah or Charmaine at our office for further details and prices on 01440 713355  

Certikin Above Ground Winter Debris Cover - -  
Certikin above ground winter covers are ideal for timber pools. Manufactured in a similar way to our classic Maple cover from green or blue woven polyethylene, the above ground cover folds just over the edge of the timber frame and secures with elasticated loops onto stainless steel hooks as opposed to straps and springs. Available for rectangular and hexagonal/octagonal pools of any size, ladder cut outs can also be accommodated.Available in Green or BlueFor more information, please follow the link belowhttp://www.certikin.co.uk/pdf/wintercovers-lft.pdfPlease phone our office and speak to Sarah or Charmaine for details and prices 01440 713355

Prevention Or Cure

Fi-Clor Multifunctional Algicide 3lt Container (Copper Free) - FIACM3 -  
5 ACTIONS IN ONE TREATMENT. Eliminates algae. Protects pool for a season. Water clarifier. Anti-stain. Anti-scale. Instructions A sanitiser must always be used as well as a long life algicide in order to kill bacteria and other harmful organisms.It is important to keep the sanitiser at recommended levels even when the pool is temporarily out of use. This will assist in the control of algae.Superchlorinate with Fi-Clor Superchlorinator every two weeks in accordance with the label instructions.For more information follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/265%20MSDS%20Fi-Clor%20Multi-Function%20Algicide.pdf

Fi-Clor Concentrated Algicide 1lt Container (Copper Free) - FIACU -  
HELPS PREVENT OR TREAT ALGAE. Highly concentrated to prolong contact with affected areas. Dual action algicide and clarifier. Compatible with all sanitisers and filters. 1 litre of this product is equivalent to 3 litres of standard algicide. Instructions – for regular treatment Starting the season 300ml per 50m3 (11,000 galls)CAUTION In hard water areas, increase the dosage by 50%.In the event of large numbers of bathers, high temperatures or heavy rain, increase the dosage. Pools that have been emptied: Clean the pool surfaces thoroughly.Using a clean, uncontaminated pail, make up a solution using 1 part Ultra Concentrated Algicide to 10 parts water.Thoroughly wash skimmers, bottom drains, outlets and liner or tile joints. Leave for about an hour before filling the pool. Treating water that has turned green: For maximum performance, adjust the pH to approx 7.2.Shock dose the pool with Fi-Clor Superfast Shock at the rate of 1.1kg per 11,000 gallons (50m3) (accuracy of dosing is not important). ( N.B. If the pool is on PHMB - shock dose with Baquacil Shock)Broadcast the product evenly over a wide area in the deepest part of the pool and keep the circulation running.Allow time for the shock to disperse, then add Ultra Concentrated Algicide either via the skimmer, or directly into the pool at a rate of 650ml per 11,000 gallons (50m3) Ensure there is no other product in the skimmer nor any bathers in the pool.Leave the product to act for 1-2 hours then brush off any algae that may be clinging to pool surfaces and agitate any areas where concentrations of product may still exist.Run the filter for 24 hours then backwash to remove dead algae from the top of the filter media.For more information follow the links belowProduct Brochurehttp://www.fi-clor.co.uk/pc_ultra_con_algi_1ltr.shtmlSafety Datahttp://www.certikin.co.uk/pdf/187%20MSDS%20Fi-Clor%20ULTRA%20Concentrated%20Algicide.pdf

Fi-Clor Extra Strong Algicide 3lt Container - FIASH3 -  
In the case of a heavy infestation or highly resistant algae, brush the pool surfaces and run the filtration continuously until the pool has cleared. Use of a clarifier will be beneficial.Destroys all types of typical algae, even the most resistantHighly concentrated compositionContains copperInstructionsDistribute evenly around the pool in the evening after bathing has finished.N.B. Adding sufficient product in one dose to provide 6 months protection could raise the copper concentration to an unacceptable level, depending on the existing copper level before dosing the algicideFor more information follow the link belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/258%20MSDS%20Fi-Clor%20Extra%20Strong%20Algicide.pdf

Fi-Clor Winteriser 3lt Container - FIW3 -  
PROTECTS YOUR POOL OVER WINTER. If you have not decommissioned your pool for the winter before, the guidelines on this pack should be of some assistance. If you are in any doubt as to your ability, call in your local pool centre or service engineer to do the job for you. InstructionsThoroughly backwash the filter. Remove any debris from the pump strainer, skimmers and pool water surface.Shock dose with a stabiliser-free chlorine such as Fi-Clor Superfast Shock to kill any algae and harmful organisms that may be present. (If your pool is treated with a non-chlorine sanitiser - PHMB, treat with Baquacil Winteriser). Allow the water to circulate for 3 – 4 hours to ensure thorough mixing.With the water still circulating via the bottom drain, add Fi-Clor Winteriser, leaving the circulation running long enough to ensure thorough mixing.For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/191%20MSDS%20Fi%20Clor%20Winteriser.pdf

Fi-Clor Clarifier Tablets 1kg Container - FICT -  
CLARIFIES POOL WATER. Suitable for all types of sand filtration. Compatible with all pool santisers. There can be a number of small particles present in suspension in pool water that are too fine to be retained by the sand filter alone. These can make pool water hazy. Use of Fi-Clor Clarifier Tablets will coagulate the particles into a size which can be retained by the filter. Using these Clarifier tablets will also improve the efficiency of your filter. Instructions: Use in cases of high turbidity, after shock dosing or after a backwash, and for weekly maintenance.CAUTION: Do not use this product with diatomite or cartridge filtration systems.For more information follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/186%20MSDS%20Fi%20Clor%20Clarifier%20Tablets.pdf

Fi-Clor Rapid Liquid Clarifier 1lt Container - FICS1 -  
TURNS CLOUDY WATER CRYSTAL CLEAR. Fast acting, powerful formula. For sand filter – improves filtering of fine particles. Can be used with filter running. Instructions After dosing Rapid Clarfier, in the event of impurities being precipitated on the pool floor, remove them by vacuuming directly to waste Caution Regularly check filter pressure.If the pressure becomes too high, backwash and rinse again to obtain a normal pressure.Do not use Rapid Clarifier with diatomite or cartridge filtration systemFor more information follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/266%20MSDS%20FI-CLOR%20RAPID%20CLARIFIER.pdf

Fi-Clor Clean Surface 1lt Container - FICL1 -  
ELIMINATES AND PREVENTS THE OILY FILM ON THE WATER SURFACE AND ON THE WATERLINE. Based on natural enzymes. Instructions When filling the pool and for maintenance treatment: Curative treatment: If an oily film should appear on the surface of the water or on the walls of the pool, add 0.6 litre of Clean Surface for each 50m3 (11,000 gals) of water.  Repeat the operation and leave the filtration running 24 hours a day until the oily film disappears.Natural enzymes digest creams, lotions and various organic substances, thus preventing the formation of an oily film on the water surface or pool wall. CAUTIONDo not shock treat your pool 48 hours before or after using Fi-Clor Clean Surface.For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdf

Fi-Clor Granular Floc 3kg Container - FIF3 -  
Clarifies pool water by total floc treatment. Removes debris following shock treatment. Instructions Once floc has settled on the pool floor, carefully vacuum as much as possible to waste – removing any remainder by normal filtration.For more information follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/261%20MSDS%20Fi%20Clor%20Granular%20Floc.pdf

Fi-Clor Stain & Scale Remover 1lt Container - FIST1 -  
REMOVES SCALE AND MINERAL STAINING. Effective on all types of pool surfaces. No unpleasant odour. Fi-Clor Stain and Scale Remover has been specially developed to help remove scale, rust stains and mineral deposits from pool surfaces, surrounds, showers and toilets. Equally effective on tiles and liners it quickly returns surfaces to look like new. Instructions: Wear gloves and eye protection. If possible, wet the surface to be cleaned.When diluting, always add product to the water, never water to product.Wipe on with natural sponge or smooth brush.If necessary brush the surfaces being cleaned (avoid the use of synthetic brushes). Rinse with plenty of water.For stubborn stains, repeat as required.For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/219%20MSDS%20Fi%20Clor%20Stain%20and%20Scale%20Remover.pdf

Fi-Clor Stain & Scale Inhibitor 2kg Container - FIST2 -  
HELPS PREVENT STAINS AND SCALE. Phosphate-free, minimises risk of algae. Non-foaming. Fi-CLOR Stain & Scale Inhibitor has been specially developed to help prevent staining by dissolved minerals, especially where the water is discoloured or where levels of iron, copper and manganese are known to be too high. It can also help prevent the formation of scale and rough deposits on pool surfaces. Use this product to prevent staining and scaling.  If pool surfaces have already been stained or scaled use Fi-Clor Stain and Scale Remover. Instructions Calculate the volume of water in your pool (if in doubt, consult the Fi-Clor Swimming Pool Handbook).If the levels of dissolved metals exceed 1.5 ppm (mg/l), double the dose.If in doubt about the levels of dissolved minerals in your pool, take a sample of pool water to your Fi-Clor pool dealer for analysis.Any haziness in the water should be removed by treating with one of the Fi-Clor water clarifiers.For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/189%20MSDS%20Fi%20Clor%20Stain%20and%20Scale%20Inhibitor.pdf

Fi-Clor Tile & Liner Cleaner 1lt Container - FITLC1 -  
REMOVES DIRT AND SCALE FROM THE WATERLINE. Fi-Clor Tile & Liner Cleaner makes it easy to clean unsightly deposits of dirt, suncream and grease along the waterline which, if untreated can become a breeding site for bacteria. Supplied as a gel it adheres better to vertical surfaces, making them easier to clean. It is compatible with all types of pool surface. Instructions: Wear gloves and eye protection. Rinse sponge or brush in fresh water after use.The diluted product does not react with pool sanitisers.For stubborn stains, repeat as required.For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/049%20MSDS%20Fi%20Clor%20Tile%20and%20Liner%20Cleaner.pdf

Submersible Pumps

Coverstar Submersible Pump - CTE1108 -  
This safety cover pump is used to remove excess water which has gathered on the material. It has an electronic 12v sensor so that when left on the pool cover it will start automatically when required.

Water Balance

Fi-Clor PH & Alkalinity Reducer (Dry Acid) 7kg Container - WB-07 -  
CORRECTS HIGH pH AND HIGH ALKALINITY. According to the method of dosing, Fi-Clor pH & Alkalinity Reducer (Dry Acid) will lower either the pH or the total alkalinity in swimming pool water. High pH can result in cloudy water and contribute to scale formation. More importantly, it will reduce the effectiveness of chlorine based sanitisers as they produce less free active chlorine. High alkalinity will make it difficult to adjust the pH as any correcting chemicals will be taken up by the alkalinity and are unable to alter the pH. Instructions to correct pH Take a pH reading using your test kit or test strips. You will need to lower the pH if the reading is above 7.6.Pre-dissolve the Fi-Clor pH & Alkalinity Reducer in pool water using a suitable container. In order to avoid concentrated solutions, only dissolve a maximum of 500g of the product in 10 litres of water at a time, adding product to water, never water to product. If you need to use more than 500g Fi-Clor pH & Alkalinity Reducer, repeat the treatment. Dose no more than a total of 1kg at a time.With the circulation system running, distribute evenly around the pool, avoiding the skimmers.Continue filtration and re-test after 24 hours. If the pH is still high, repeat the doTo correct total alkalinity Determine the total alkalinity level using a test kit or test strips. If the reading is above 200mg/l (ppm), pre-dissolve 1kg of the product as described, and pour the solution in a small area at the deep end of the pool. Each application will reduce the alkalinity by approx 10 – 20mg/l.Re-test after 24 hours. If the total alkalinity is still high, repeat the dose until total alkalinity falls below 200mg/l (ppm), varying the location slightly but avoiding the skimmers.For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/042%20MSDS%20Fi%20Clor%20pH%20and%20Alkalinity%20Reducer.pdfIf you are unsure or unable to test please call our office for our assistance 01440 713355

Fi-Clor PH & Alkalinity Reducer (Dry Acid) 25kg Container - WB-25 -  
CORRECTS HIGH pH AND HIGH ALKALINITY. According to the method of dosing, Fi-Clor pH & Alkalinity Reducer (Dry Acid) will lower either the pH or the total alkalinity in swimming pool water. High pH can result in cloudy water and contribute to scale formation. More importantly, it will reduce the effectiveness of chlorine based sanitisers as they produce less free active chlorine. High alkalinity will make it difficult to adjust the pH as any correcting chemicals will be taken up by the alkalinity and are unable to alter the pH. Instructions to correct pH Take a pH reading using your test kit or test strips. You will need to lower the pH if the reading is above 7.6.Pre-dissolve the Fi-Clor pH & Alkalinity Reducer in pool water using a suitable container. In order to avoid concentrated solutions, only dissolve a maximum of 500g of the product in 10 litres of water at a time, adding product to water, never water to product. If you need to use more than 500g Fi-Clor pH & Alkalinity Reducer, repeat the treatment. Dose no more than a total of 1kg at a time.With the circulation system running, distribute evenly around the pool, avoiding the skimmers.Continue filtration and re-test after 24 hours. If the pH is still high, repeat the doTo correct total alkalinity Determine the total alkalinity level using a test kit or test strips. If the reading is above 200mg/l (ppm), pre-dissolve 1kg of the product as described, and pour the solution in a small area at the deep end of the pool. Each application will reduce the alkalinity by approx 10 – 20mg/l.Re-test after 24 hours. If the total alkalinity is still high, repeat the dose until total alkalinity falls below 200mg/l (ppm), varying the location slightly but avoiding the skimmers.For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/042%20MSDS%20Fi%20Clor%20pH%20and%20Alkalinity%20Reducer.pdfIf you are unsure or unable to test please call our office for our assistance 01440 713355

Fi-Clor PH Increaser (Soda Ash) 5kg Container - WB+05 -  
Fi-Clor pH Increaser (Soda Ash) is for raising the pH level in swimming pool water. pH is a measure of how acid or how alkaline the water is. Low pH can lead to skin irritation and corrosion of equipment. Instructions to correct pH Take a pH reading using your test kit or test strips. You will need to raise the pH if the reading is below 7.2.Pre-dissolve the Fi-Clor pH Increaser in pool water using a suitable container. In order to avoid concentrated solutions, only dissolve a maximum of 500g of the product in 10 litres of water at a time, adding product to water, never water to product. If you need to use more than 500g Fi-Clor pH Increaser repeat the treatment. Dose no more than a total of 1kg at a time.With the circulation system running, distribute evenly around the pool, avoiding the skimmers.Continue filtration and re-test after 24 hours. If the pH is still low, repeat the dose.For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/048%20MSDS%20Fi%20Clor%20pH%20Increaser.pdf

Fi-Clor Alkalinity Increaser 5kg Container - WBA05 -  
CORRECTS LOW TOTAL ALKALINITY. Fi-Clor Alkalinity Increaser (Bicarbonate) is for raising the total alkalinity level in swimming pool water. Alkalinity is a measure of the amount of alkali (or in chemical terms, bicarbonates and carbonates) in the water. If the alkalinity is too low, any chemicals added to the pool will directly affect the pH, causing rapid fluctuations in pH readings. Alkalinity at the correct level will help protect, or 'buffer' the pH. Instructions Take an alkalinity reading on your test kit. You will need to raise the total alkalinity if the reading is below 100mg/l (ppm) for pools sanitised with stabilised chlorine's or bromine, or below 80mg/l (ppm) for pools sanitised with Fi-Clor Superfast or Supercapsules.Pre-dissolve the Fi-Clor Alkalinity Increaser in pool water using a suitable container. In order to avoid concentrated solutions, only dissolve a maximum of 500g of the product in 10 litres of water at a time, adding product to water, never water to product. Dose no more than a total of 1.5kg in a day.With the circulation system running, distribute evenly around the pool, avoiding the skimmers.Continue filtration and re-test after 24 hours. If the total alkalinity is still low, repeat the dose.For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/048%20MSDS%20Fi%20Clor%20pH%20Increaser.pdfIf you are unsure or unable to test please call our office for our assistance 01440 713355

Fi-Clor Chlorine Stabiliser 3kg Container - FIS03 -  
Fi-Clor Chlorine Stabiliser protects pool chlorine in outdoor pools and reduces wasteful loss of sanitiser to sunlight. Ideal for pools on stabiliser free chlorine's. Instructions Calculate the volume of water in your pool (if in doubt, consult the Fi-Clor Swimming Pool Handbook).Take a cyanuric acid reading using your test kit. If the reading is below 30mg/l (ppm) you will need to add Fi-Clor Chlorine Stabiliser as above.The Chlorine Stabiliser can take a few days to dissolve. During this period assist dissolution by sweeping any accumulated product with a pool brush keeping filters running. Do not backwashNote When filling a pool, a single dose of 1.5kg of Chlorine Stabiliser should be added during or immediately after filling the pool.For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/037%20MSDS%20Fi%20Clor%20Stabilizer.pdfIf you are unsure or unable to test please call our office for our assistance 01440 713355

Fi-Clor Calcium Hardness Increaser 4kg Container - WBC4 -  
CORRECTS LOW CALCIUM HARDNESS. Fi-Clor Hardness Increaser is for raising the calcium hardness level in swimming pool water. Calcium hardness is the amount of dissolved calcium and magnesium in pool water. If there is insufficient dissolved calcium, the water will try and take it from the grouting and concrete in the pool. High levels are not a major cause for concern provided the pH and alkalinity are within recommended parameters, but the reading should be kept below 1000mg/l (ppm) if possible. Instructions Take a calcium hardness reading using your test kit. You will need to correct the calcium hardness if the reading is below 175mg/l (ppm) for liner pools, and below 250mg/l (ppm) for tiled pools.With the circulation system running, sprinkle the product directly into the water around the perimeter of the pool. Do not pre-dissolve as this could generate excessive heat. Only use when bathing has ceased, and avoid areas near the skimmers.Re-test after 24 hours. If the calcium hardness level is still below 175mg/l (ppm) for liner pools, and 250mg/l (ppm) for tiled pools, repeat the dose. For more information please follow the links belowProduct Brochurehttp://www.certikin.co.uk/pdf/Fi-Clor-swimpool-handbook-2007-low-res.pdfSafety Datahttp://www.certikin.co.uk/pdf/163%20MSDS%20Fi%20Clor%20Hardness%20Increaser.pdfIf you are unsure or unable to test please call our office for our assistance 01440 713355

Pump Accessories

Pump Anti Vibration Pad - 8485 -  
Anti Vibration Pad for Pumps 10" x 9" x 1.5"

1.5" Anti Vibration/Repair Fitting - CP15PSR -  
1.5" x 1.5" PP Socket Anti Vibration Pad/Repair Fitting

2" Anti Vibration Pad/Repair Fitting - CP2PSR -  
2" x 2" PP Socket Anti Vibration Pad/Repair Fitting

Safety Covers, Summer Solar Covers & Winter Covers

Water Treatment

Latest News :

  Neptune Swimming Pools would like to wish all their customers a Happy New Year! [ 03-01-2012 ]
  Come & Join Our Growing Company! [ 08-11-2011 ]
  Neptune Swimming Pools are now taking swimming pool bookings in the Suffolk, Essex, Cambridge and Norfolk areas for 2012. [ 23-10-2011 ]

 







Web Design : Pure Energy